Voltage Divider Calculator

View results · 3.837 V

Divider

Solve for

Resistances accept plain ohms or prefixes such as 4.7k, 4k7, 220 or 1M. Leave the load empty for an unloaded divider.

Result

Output voltage
Division ratio
0.3197
Divider current
0.8163 mA
Power in R1
6.664 mW
Power in R2
3.132 mW
VinR1R2Vout
Vout=12×470010000+4700≈3.837 VV_{out}=12\times\frac{4700}{10000+4700}\approx3.837\,\text{V}

About this tool

A voltage divider uses two resistors in series to produce a fraction of an input voltage. It is one of the most common circuits in electronics: it scales a sensor or battery voltage down to the range of an analog-to-digital converter, sets bias points for transistors, creates reference voltages and shifts logic levels.

The output depends only on the ratio of the resistors when nothing draws current from it. A real load acts as a third resistor in parallel with R2 and pulls the output down, so a divider works best when the load resistance is much larger than R2, typically ten times or more.

How it works

Choose what to solve for. To find the output voltage, enter the input voltage and both resistors. To design a divider, enter the input voltage, the output voltage you need and one resistor, and the calculator finds the other one. Resistances can be typed as 4700, 4.7k or 4k7.

The output of an unloaded divider is Vout=Vin R2/(R1+R2)V_{out} = V_{in}\,R_2 / (R_1 + R_2). If you enter a load resistance, the calculator replaces R2 with R2 in parallel with the load, R2RL/(R2+RL)R_2 R_L / (R_2 + R_L), which lowers the output. It also shows the current through the divider, the power each resistor dissipates and, when it solves for a resistor, the nearest E12 and E24 standard values with the voltage they would actually give.

Vout=Vin R2R1+R2V_{out}=V_{in}\,\frac{R_2}{R_1+R_2}

Example

To read a 12 V battery with a 5 V microcontroller input, choose R1=10 kΩR_1 = 10\ \text{k}\Omega and solve for R2: R2=R1VoutVin−Vout=10000×57≈7143 ΩR_2 = R_1 \frac{V_{out}}{V_{in} - V_{out}} = 10000 \times \frac{5}{7} \approx 7143\ \Omega. The nearest E24 value, 7.5 kΩ, gives 12×7.517.5≈5.1412 \times \frac{7.5}{17.5} \approx 5.14 V, slightly above 5 V, while the E12 value 6.8 kΩ gives a safer 4.86 V.

With 10 kΩ and 4.7 kΩ on 12 V, the unloaded output is 12×4.714.7≈3.8412 \times \frac{4.7}{14.7} \approx 3.84 V and the divider draws about 0.82 mA.

Standard resistor values

E24 series (IEC 60063), with the values that are also in E12

E24 valueAlso in E12Examples
1Yes100 Ω, 1 kΩ, 10 kΩ
1.1—110 Ω, 1.1 kΩ, 11 kΩ
1.2Yes120 Ω, 1.2 kΩ, 12 kΩ
1.3—130 Ω, 1.3 kΩ, 13 kΩ
1.5Yes150 Ω, 1.5 kΩ, 15 kΩ
1.6—160 Ω, 1.6 kΩ, 16 kΩ
1.8Yes180 Ω, 1.8 kΩ, 18 kΩ
2—200 Ω, 2 kΩ, 20 kΩ
2.2Yes220 Ω, 2.2 kΩ, 22 kΩ
2.4—240 Ω, 2.4 kΩ, 24 kΩ
2.7Yes270 Ω, 2.7 kΩ, 27 kΩ
3—300 Ω, 3 kΩ, 30 kΩ
3.3Yes330 Ω, 3.3 kΩ, 33 kΩ
3.6—360 Ω, 3.6 kΩ, 36 kΩ
3.9Yes390 Ω, 3.9 kΩ, 39 kΩ
4.3—430 Ω, 4.3 kΩ, 43 kΩ
4.7Yes470 Ω, 4.7 kΩ, 47 kΩ
5.1—510 Ω, 5.1 kΩ, 51 kΩ
5.6Yes560 Ω, 5.6 kΩ, 56 kΩ
6.2—620 Ω, 6.2 kΩ, 62 kΩ
6.8Yes680 Ω, 6.8 kΩ, 68 kΩ
7.5—750 Ω, 7.5 kΩ, 75 kΩ
8.2Yes820 Ω, 8.2 kΩ, 82 kΩ
9.1—910 Ω, 9.1 kΩ, 91 kΩ

Each series repeats in every decade, so 4.7 stands for 4.7 Ω, 47 Ω, 470 Ω, 4.7 kΩ and so on.

Assumptions and limits

The calculation assumes ideal resistors and a steady DC (or resistive AC) input. Real resistors have a tolerance, typically ±1% or ±5%, so the actual output varies. The source must be able to supply the divider current, and the resistors must be rated for the power they dissipate.

A voltage divider is not a power supply: the output voltage changes with the load current. To power a circuit, use a voltage regulator instead.

Frequently asked questions

What is the voltage divider formula?

Vout=Vin×R2/(R1+R2)V_{out} = V_{in} \times R_2 / (R_1 + R_2), where R1 connects the input to the output and R2 connects the output to ground.

How do I choose resistor values for a voltage divider?

Pick the ratio from the voltages, then the size from the current you can afford. Higher values waste less power but make the output more sensitive to the load and to noise; values from 1 kΩ to 100 kΩ suit most signal dividers.

How does a load affect a voltage divider?

The load is in parallel with R2, so the lower part of the divider has less resistance and the output voltage drops. Keep the load at least ten times larger than R2, or buffer the output.

What are E12 and E24 resistor values?

They are the IEC 60063 preferred number series with 12 or 24 values per decade, such as 1.0, 1.2, 1.5, 1.8, 2.2, 2.7, 3.3, 3.9, 4.7, 5.6, 6.8 and 8.2 for E12. Resistors are commonly sold in these values, with E24 parts usually at 5% or 1% tolerance.

Can I use a voltage divider to power a device?

Usually not. The output voltage falls as soon as the device draws current, and the divider wastes power continuously. Use a linear regulator or a switching converter to supply power.

Link with your values

Add these parameters to this page’s address to open it with the values filled in, for example to share a calculation or to link to it from an AI assistant. The result is calculated in the browser: the page HTML shows an example for the default values, and the tool sets the data-url-params attribute once the link’s values are applied.

ParameterValueIf omitted
solve_forwhat to calculate: output_voltage, r1, r2; give the other 2 valuesdefault output_voltage
input_voltage_vInput voltagenumber; allowed > 0 – < 1000000000000000required
output_voltage_vTarget output voltagenumber; allowed > 0 – < 1000000000000000give 2 of output_voltage_v, r1_ohm, r2_ohm
r1_ohmR1, top resistornumber; allowed > 0 – < 1000000000000000give 2 of output_voltage_v, r1_ohm, r2_ohm
r2_ohmR2, bottom resistornumber; allowed > 0 – < 1000000000000000give 2 of output_voltage_v, r1_ohm, r2_ohm
load_ohmLoad resistancenumber; allowed > 0 – < 1000000000000000optional

Examples

  • ?input_voltage_v=9&r1_ohm=10000&r2_ohm=20000
  • ?solve_for=r2&input_voltage_v=5&output_voltage_v=3.3&r1_ohm=10000
  • ?input_voltage_v=24&output_voltage_v=5&r2_ohm=4700&load_ohm=100000

Write decimals with a point. Encode a space as %20, + as %2B, # as %23 and & as %26.

Result elements: [data-result-block="voltage-divider"]