Playback Speed Calculator

Enter recording duration and a positive playback multiplier. A multiplier below 1 increases listening time, so time saved becomes negative. Results are displayed in seconds.

Results

Enter your values and select Calculate.

tplay=t/st_{play}=t/s

About this tool

This playback speed calculator shows how long a video, podcast, lecture or audiobook takes to finish at a chosen speed, and how much time that saves compared with normal speed. It helps when planning study sessions or a commute. Playback time equals the original duration divided by the speed multiplier, so 2× halves the listening time. Speeds below 1 slow playback down and make it longer.

How it works

Enter the length of the recording in one of three formats: plain seconds such as 2700, minutes and seconds such as 45:00, or hours, minutes and seconds such as 1:30:00. Then type the speed multiplier from your player, for example 1.25, 1.5 or 0.75.

The calculator converts the duration to seconds, divides it by the speed and subtracts the result from the original length to show the time saved. Both results are in seconds, so divide by 60 for minutes. A speed above 1 gives a positive saving, and a speed below 1 gives a negative one.

tplay=t/st_{play}=t/s

Example

The default recording is 1:00:00 long, which is 3,600 seconds, played at 1.5×. Playback time is 3600/1.5=24003600 / 1.5 = 2400 seconds, or 40 minutes. Time saved is 3600−2400=12003600 - 2400 = 1200 seconds, or 20 minutes. At 1.5× you save one third of the original length, not half, because the saved fraction equals 1−1/s1 - 1/s.

Assumptions and limits

Durations are entered as seconds, M:SS or H:MM:SS, and results are shown in seconds. The tool assumes one constant speed for the whole recording and does not account for skipped silence, ads, chapter jumps or pauses. A speed below 1 produces a negative time saved, meaning playback takes longer than the original.

Frequently asked questions

How long is a 10-hour audiobook at 2× speed?

It takes 5 hours, because the playback time is the duration divided by the speed. At 1.5× the same book takes about 6 hours 40 minutes. A 10-hour book is 36,000 seconds, so entering 10:00:00 and a speed of 2 shows 18,000 seconds of playback.

Does 1.5× speed save half the time?

No. At 1.5× the playback lasts two thirds of the original, so you save one third. Only 2× saves half the time. In general, the share of time saved is 1−1/s1 - 1/s, so 1.25× saves 20% and 1.75× saves about 43%.

Does faster playback change the pitch of voices?

Most current video and podcast players apply pitch correction, so voices sound faster but not higher. Simple players without correction raise the pitch along with the speed. This calculator only works out the time; how the audio sounds depends on your player's settings.

How do I find the speed needed to finish in a set time?

Divide the original duration by the time you have. For example, a 90-minute lecture watched in 60 minutes needs 1.5× speed. Many players only offer fixed steps such as 1.25×, 1.5× and 1.75×, so round up to the next available step to finish on time.

How much time does 1.25× save on a one-hour video?

A one-hour video is 3,600 seconds, and at 1.25× it plays in 2,880 seconds, which is 48 minutes. You save 12 minutes, or 20% of the original length. Across a 12-week course with three hours of lectures a week, the same speed saves more than 7 hours.

Link with your values

Add these parameters to this page’s address to open it with the values filled in, for example to share a calculation or to link to it from an AI assistant. The result is calculated in the browser: the page HTML shows an example for the default values, and the tool sets the data-url-params attribute once the link’s values are applied.

ParameterValueIf omitted
durationDuration (H:MM:SS or M:SS)duration: m:ss or h:mm:ss; allowed ≥ 0required
playback_speedPlayback speednumber; allowed > 0required

Examples

  • ?duration=1:30:00&playback_speed=1.25

Write decimals with a point. Encode a space as %20, + as %2B, # as %23 and & as %26.

Result elements: [data-result-block="playback_speed_calculator"]