About this tool
A gear ratio tells you how a pair or a chain of gears trades speed for torque. A small gear driving a larger one turns it more slowly but with more force; the reverse speeds it up. The same arithmetic sizes gearboxes, robot drives, winches and 3D printer extruders, and it is how cyclists compare one gear with another.
In a simple chain of meshing gears only the first and the last gear matter: idler gears in between change the direction of rotation but not the ratio. Bicycle gears are compared in gear inches or development because the wheel size matters as much as the teeth.
How it works
In gear train mode, enter the teeth on the driving gear and on the driven gear for each stage. The ratio of a stage is , and the ratios of several stages multiply. Add the input speed to get the output speed , and the input torque to get the output torque , where is the efficiency of each of the stages.
In bicycle mode, enter the chainring and the rear cog and choose a wheel size. The ratio is chainring teeth divided by cog teeth. Gear inches multiply the ratio by the wheel diameter in inches, and development (rollout) is the distance the bike travels for one turn of the cranks: the wheel circumference times the ratio. Add a cadence to see your speed, and a list of cogs to compare a whole cassette.
Example
A 12-tooth motor pinion drives a 36-tooth gear, and a 15-tooth gear on the same shaft drives a 45-tooth gear. The stage ratios are and , so the overall ratio is 9 : 1. A motor at 1800 rpm turns the output at rpm, and 10 N·m of input torque becomes N·m with 98% efficiency per stage.
On a road bike with a 700×23C tire (about 668 mm), a 53-tooth chainring and a 12-tooth cog give a ratio of , about 116 gear inches and 9.27 meters per pedal turn. At a cadence of 90 rpm that is about 50 km/h.
Assumptions and limits
Tooth counts give the exact ratio for gears, sprockets and toothed belts. Friction belts can slip slightly, and the efficiency you enter is an estimate: well-lubricated spur gear stages are often 95–99% efficient, while worm gears can be far lower. Torque results assume a steady load and ignore inertia.
Bicycle wheel diameters are estimated from the ISO rim size plus twice the tire width; real tires differ by brand, width and pressure. For a precise speed, measure your wheel's rollout.
Frequently asked questions
How do you calculate a gear ratio?
Divide the number of teeth on the driven gear by the number on the driving gear. A 10-tooth gear driving a 40-tooth gear has a ratio of 4 : 1: the output turns four times more slowly and, ignoring losses, with four times the torque.
How do I calculate the ratio of several gears?
Multiply the ratios of the stages, where a stage is a driving gear and the gear it meshes with. Gears that share a shaft turn at the same speed and start the next stage. Idler gears between two gears on separate shafts do not change the ratio.
How does the gear ratio affect speed and torque?
Output speed is the input speed divided by the ratio, and output torque is the input torque multiplied by the ratio and the efficiency. Power stays the same apart from friction losses, so you trade one for the other.
What are gear inches on a bike?
Gear inches are the diameter of the drive wheel in inches multiplied by the chainring-to-cog ratio. The measure dates from high-wheel bicycles: a 60-inch gear feels like riding a wheel 60 inches across. Low climbing gears are around 20–40 inches and high road gears around 100–130 inches.
What is development or rollout?
Development is the distance the bike moves for one full turn of the pedals: the wheel circumference times the gear ratio. It is the usual measure in Europe, and some junior racing rules use it to limit gearing.
Link with your values
Add these parameters to this page’s address to open it with the values filled in, for example to share a calculation or to link to it from an AI assistant. The result is calculated in the browser: the page HTML shows an example for the default values, and the tool sets the data-url-params attribute once the link’s values are applied.
| Parameter | Value | If omitted |
|---|---|---|
modeCalculate | one of: train, bike | default train |
input_rpmInput speed | number; allowed 0–1000000; used with mode = train | optional |
torque_nmInput torque | number; allowed 0–1000000000; used with mode = train | optional |
torque_lb_ftInput torque | number; allowed 0–1000000000; used with mode = train | optional |
efficiency_pctEfficiency per stage | percent: 6.5 means 6.5%; allowed 1–100; used with mode = train | default 98 |
chainringChainring teeth | whole number; allowed 10–80; used with mode = bike | required |
cogCog teeth | whole number; allowed 6–60; used with mode = bike | required |
wheel_sizeWheel and tire | one of: road700x25, road700x28, road700x32, gravel700x40, mtb29x225, mtb275x225, mtb26x21, bmx20x175, custom; used with mode = bike | default road700x28 |
wheel_diameter_mmWheel diameter | number; any unit in the name: _mm, _cm, _m, _km, _in, _ft, _yd, _mi, _nmi; allowed 200–1000 mm; used with mode = bike | calculated by the tool |
cadenceCadence | number; allowed 0–250; used with mode = bike | optional |
speed_unitSpeed unit | one of: kmh, mph; used with mode = bike | default mph |
cassetteCassette cogs | values separated by commas: 2,4,4,6; allowed 6–60; used with mode = bike | optional |
| Parameter | Value | If omitted |
|---|---|---|
stage1_driverDriver teeth | whole number; allowed 1–10000 | required |
stage1_drivenDriven teeth | whole number; allowed 1–10000 | required |
Examples
?stage1_driver=10&stage1_driven=40&stage2_driver=12&stage2_driven=30&input_rpm=3000&torque_nm=12&efficiency_pct=97?chainring=52&cog=13&wheel_size=road700x25&cadence=95&speed_unit=kmh&cassette=11,12,13,14,16,18,21,24,28?mode=bike&chainring=34&cog=28&wheel_diameter_mm=650
Write decimals with a point. Encode a space as %20, + as %2B, # as %23 and & as %26.
Result elements: [data-result-block="gear-ratio"]