Gravel Calculator

View results · 2.1 tons

Your project

Units

Areas

Area 1

Area: 120 ft²

Typical depths: 2–3 in for paths and beds, 4–6 in for driveways.

Type of gravel

Typical density: 1.6 t/m³ (1.35 tons/yd³).

Price quoted

Result

Short tons (incl. 5% extra)
tons
Volume
1.56 yd³
Pounds
4,195 lb
Bags of 0.5 cu ft
84
Total area
120 ft²
Volume without extra
1.48 yd³
V=A d12=120×412≈40 ft3=4027≈1.48 yd3V=\frac{A\,d}{12}=\frac{120\times4}{12}\approx40\,\text{ft}^3=\frac{40}{27}\approx1.48\,\text{yd}^3
V′=V(1+w100)≈1.556 yd3V'=V\left(1+\frac{w}{100}\right)\approx1.556\,\text{yd}^3
m=V′ρ=1.556×1.348≈2.1 tonsm=V'\rho=1.556\times1.348\approx2.1\,\text{tons}

Weights use the selected density. Quarries and garden centres may quote slightly different figures, so ask for theirs before ordering.

About this tool

Gravel is ordered by volume or by weight, and the conversion between the two depends on the stone. A cubic yard of gravel typically weighs about 1.2 to 1.5 short tons, roughly 1.4 to 1.7 tonnes per cubic metre, depending on the rock, the size and grading of the stones and how wet they are.

The right depth depends on the job. Paths and decorative beds usually need 2–3 in (5–8 cm). A gravel driveway is commonly built in layers about 4–6 in (10–15 cm) thick in total, with larger crushed stone at the bottom and finer stone on top. Angular crushed stone locks together and suits driveways and bases; round pea gravel and river rock stay loose and suit paths, play areas and drainage.

How it works

Describe the area to cover with one or more rectangles, circles or triangles, enter the depth and choose a type of gravel. The calculator finds the volume, adds your extra allowance and multiplies by the stone's density to estimate the weight, which is how gravel is usually sold.

Pea gravel, crushed stone and river rock use typical loose densities from engineering reference tables. If your supplier quotes a different figure, such as 1.4 tons per cubic yard, choose the custom option and enter it. Prices can be entered per ton or per cubic yard (per tonne or per cubic metre in metric units). Bag counts assume 0.5 cu ft bags in US units and 25 kg bags in metric units.

m=A⋅d324⋅ρm = \frac{A \cdot d}{324} \cdot \rho

Example

A driveway 40 ft long and 10 ft wide, covered 4 in deep with crushed stone, has a volume of 400×4÷12≈133.3400 \times 4 \div 12 \approx 133.3 ft³, or 133.3÷27≈4.94133.3 \div 27 \approx 4.94 yd³. With 5% extra, that becomes about 5.19 yd³.

At 1.6 tonnes per cubic metre, crushed stone weighs about 1.35 short tons per cubic yard, so the order is 5.19×1.35≈7.05.19 \times 1.35 \approx 7.0 tons. At $40 per ton, the stone costs about $280 before delivery. The same amount in 0.5 cu ft bags would take 280 bags.

Gravel reference tables

Typical loose densities

Type of gravelt/m³tons/yd³lb/yd³
Pea gravel1.521.282,562
Crushed stone1.61.352,697
River rock1.681.422,832

Area covered by one short ton

Depth (in)Pea gravel (ft²)Crushed stone (ft²)River rock (ft²)
2126120114
3848076
4636057
6424038

Area covered by one tonne

Depth (cm)Pea gravel (m²)Crushed stone (m²)River rock (m²)
513.212.511.9
7.58.88.37.9
106.66.36
154.44.24

Gravel bags

Bag sizeBags per cubic yardBags per ton of crushed stone
0.5 ft³5440

Densities are typical values for dry, loose stone from the Engineering ToolBox table of material densities. Coverage ignores compaction and waste.

Assumptions and limits

The densities are typical values for dry, loose stone. Real weights vary by quarry, stone size and moisture: wet gravel is noticeably heavier, and fine material filling the gaps between stones raises the weight per yard. Use your supplier's density figure when you have it.

Compaction reduces the thickness of crushed stone, so order extra for driveways and bases, and remember that sub-base layers, edging and landscape fabric are separate items. The calculator estimates material only; it does not design a driveway for heavy vehicles or soft ground.

Frequently asked questions

How many tons of gravel are in a cubic yard?

Usually about 1.2 to 1.5 short tons. With the typical densities used here, a cubic yard of pea gravel weighs about 1.28 tons, crushed stone about 1.35 tons and river rock about 1.42 tons. Wet or densely graded material, such as crusher run, weighs more.

How many square feet does a ton of gravel cover?

At 2 in deep, a ton of crushed stone covers about 120 ft²; at 4 in, about 60 ft². Thinner layers cover more ground, so check the coverage table on this page for your depth and type of gravel.

How deep should gravel be?

For paths and decorative areas, 2–3 in (5–8 cm) is common. Gravel driveways usually have 4–6 in (10–15 cm) or more of compacted crushed stone over firm ground, often laid in two or three layers. Check local guidance for heavy traffic or soft soil.

How many bags of gravel make a cubic yard?

A cubic yard is 27 ft³, so it takes 54 bags of 0.5 cu ft, each weighing roughly 50 lb. For more than a cubic yard or two, bulk delivery is usually cheaper than bags.

What is the difference between pea gravel, crushed stone and river rock?

Pea gravel is small, rounded stone that is comfortable underfoot but shifts under tires. Crushed stone has sharp, angular faces that lock together, so it compacts into a firm surface for driveways and bases. River rock is larger and smooth and is used mainly for drainage and decoration.

Link with your values

Add these parameters to this page’s address to open it with the values filled in, for example to share a calculation or to link to it from an AI assistant. The result is calculated in the browser: the page HTML shows an example for the default values, and the tool sets the data-url-params attribute once the link’s values are applied.

ParameterValueIf omitted
unitsmetric or imperialset by the first measured value
currencyISO 4217 code, for example USD or EURyour saved or detected currency
depth_cmdepth_inDepthnumber; any unit in the name: _mm, _cm, _m, _km, _in, _ft, _yd, _mi, _nmi; allowed > 0 – 300 cm (metric), > 0 – 118.11 in (imperial)required
waste_pctExtra allowancepercent: 6.5 means 6.5%; allowed 0–100default 5
materialType of gravelone of: pea, crushed, river, customdefault crushed
density_ton_per_yd3Densitynumber; allowed 0.2528–4.214calculated by the tool
density_t_per_m3Densitynumber; allowed 0.3–5calculated by the tool
price_per_m3price_per_yd3Price per cubic yardamount without a currency symbol; a time per unit in the name: _per_ml, _per_l, _per_m3, _per_tsp, _per_tbsp, _per_fl_oz, _per_fl_oz_uk, _per_cup, _per_pt, _per_qt, _per_gal, _per_gal_uk, _per_in3, _per_ft3, _per_yd3, _per_ul, _per_cm3; allowed 0–1000000000 /m3 (metric), 0–1000000000 /yd3 (imperial)optional
price_per_tonPrice per tonamount without a currency symbol; allowed 0–1000000000optional
price_per_tonnePrice per tonneamount without a currency symbol; allowed 0–1000000000optional
Areas — rows numbered from 1, at most 8; every field of a row is needed
ParameterValueIf omitted
area1_shapeShapeone of: rectangle, circle, trianglecounted as rectangle
area1_length_ftLengthnumber; any unit in the name: _mm, _cm, _m, _km, _in, _ft, _yd, _mi, _nmi; allowed > 0 – 32808.4 ft; used with area1_shape = rectanglerequired
area1_width_ftWidthnumber; any unit in the name: _mm, _cm, _m, _km, _in, _ft, _yd, _mi, _nmi; allowed > 0 – 32808.4 ft; used with area1_shape = rectanglerequired
area1_diameter_ftDiameternumber; any unit in the name: _mm, _cm, _m, _km, _in, _ft, _yd, _mi, _nmi; allowed > 0 – 32808.4 ft; used with area1_shape = circlerequired
area1_base_ftBasenumber; any unit in the name: _mm, _cm, _m, _km, _in, _ft, _yd, _mi, _nmi; allowed > 0 – 32808.4 ft; used with area1_shape = trianglerequired
area1_height_ftHeightnumber; any unit in the name: _mm, _cm, _m, _km, _in, _ft, _yd, _mi, _nmi; allowed > 0 – 32808.4 ft; used with area1_shape = trianglerequired

Examples

  • ?area1_length_ft=30&area1_width_ft=12&depth_in=3&material=pea&price_per_ton=45
  • ?currency=EUR&area1_shape=triangle&area1_base_m=8&area1_height_m=5&depth_cm=8&density_t_per_m3=1.75&price_per_m3=38

Write decimals with a point. Encode a space as %20, + as %2B, # as %23 and & as %26.

Result elements: [data-result-block="material"]