About this tool
A cubic yard is the volume of a cube 3 feet on each side: 27 cubic feet, or about 0.765 cubic metres. In the United States, bulk topsoil, compost, mulch, gravel, sand and ready-mix concrete are all ordered by the cubic yard, so most landscaping and building projects start by turning a measured area and depth into yards.
The result works for any material, because volume does not depend on what fills it. For stone and asphalt, which are sold by weight, the Gravel and Asphalt calculators also convert the volume to tons. For bagged concrete, use the Concrete Calculator.
How it works
Choose US or metric units, then describe the area you want to fill: a rectangle (length and width), a circle (diameter) or a triangle (base and height). Add more areas for an L-shaped bed or a patio with a rounded end; the calculator adds them together. Then enter the depth in inches or centimetres.
The area is multiplied by the depth to give the volume. In US units, the depth in inches is divided by 12 to turn it into feet, and the cubic feet are divided by 27, because a cubic yard is a cube 3 ft on each side. An optional extra allowance covers spillage, uneven ground and settling, and a price per cubic yard (or cubic metre) gives an estimated cost.
Example
A garden bed 12 ft long and 10 ft wide, filled 4 in deep with topsoil, has an area of ft². Its volume is ft³, which is yd³.
With 10% extra you would order about yd³. Many suppliers sell in quarter or half yards, so round up to 1.75 yd³. At $45 per cubic yard, that much soil costs about $79 before delivery.
Cubic yard reference tables
Area covered by one cubic yard
| Depth (in) | Area covered (ft²) |
|---|---|
| 1 | 324 |
| 2 | 162 |
| 3 | 108 |
| 4 | 81 |
| 6 | 54 |
| 8 | 40.5 |
| 12 | 27 |
Area covered by one cubic metre
| Depth (cm) | Area covered (m²) |
|---|---|
| 2.5 | 40 |
| 5 | 20 |
| 7.5 | 13.33 |
| 10 | 10 |
| 15 | 6.67 |
| 20 | 5 |
| 30 | 3.33 |
Volume unit conversions
| Volume | ft³ | yd³ | m³ | L |
|---|---|---|---|---|
| 1 ft³ | 1 | 0.037 | 0.0283 | 28.3 |
| 1 yd³ | 27 | 1 | 0.7646 | 764.6 |
| 1 m³ | 35.31 | 1.308 | 1 | 1,000 |
Coverage is the volume divided by the depth, without any allowance for settling or waste.
Assumptions and limits
The result is a geometric volume. Loose materials change once they are placed: topsoil and compost settle after watering, gravel compacts under traffic, and wet material is heavier and bulkier than dry. That is why an allowance of 5–10% is common; use more for uneven ground or when the depth varies across the area.
Measure the depth you want after settling or compaction, and split irregular areas into rectangles, circles and triangles. For structural concrete, footings or retaining walls, follow the plans and your supplier's advice rather than a simple volume estimate.
Frequently asked questions
How many cubic feet are in a cubic yard?
27. A cubic yard measures 3 ft on each side, so it holds ft³. To convert cubic feet to cubic yards, divide by 27; to convert cubic yards to cubic metres, multiply by 0.7646.
How much area does one cubic yard cover?
At 1 in deep, one cubic yard covers 324 ft². Divide 324 by the depth in inches: about 108 ft² at 3 in, 81 ft² at 4 in and 54 ft² at 6 in. The tables on this page list more depths, including metric ones.
How do I calculate cubic yards for a circle or a triangle?
For a circle with diameter , the area is ; for a triangle, it is half the base times the height. Multiply the area in square feet by the depth in feet and divide by 27. Choose the shape for each area and the calculator does this for you.
How much does a cubic yard weigh?
It depends on the material. Dry wood mulch weighs roughly 400–800 lb per cubic yard, topsoil about a ton, gravel around 2,500–2,900 lb and concrete about 4,000 lb. For stone and asphalt, the Gravel and Asphalt calculators convert the volume to weight.
Should I order extra?
Usually, yes. An allowance of 5–10% covers spillage, an uneven base and settling, and running short often costs more than a small surplus because a second delivery has its own fee. Suppliers commonly sell in steps of a quarter or half cubic yard.
Link with your values
Add these parameters to this page’s address to open it with the values filled in, for example to share a calculation or to link to it from an AI assistant. The result is calculated in the browser: the page HTML shows an example for the default values, and the tool sets the data-url-params attribute once the link’s values are applied.
| Parameter | Value | If omitted |
|---|---|---|
units | metric or imperial | set by the first measured value |
currency | ISO 4217 code, for example USD or EUR | your saved or detected currency |
depth_cmdepth_inDepth | number; any unit in the name: _mm, _cm, _m, _km, _in, _ft, _yd, _mi, _nmi; allowed > 0 – 300 cm (metric), > 0 – 118.11 in (imperial) | required |
waste_pctExtra allowance | percent: 6.5 means 6.5%; allowed 0–100 | default 0 |
price_per_m3price_per_yd3Price per cubic yard | amount without a currency symbol; a time per unit in the name: _per_ml, _per_l, _per_m3, _per_tsp, _per_tbsp, _per_fl_oz, _per_fl_oz_uk, _per_cup, _per_pt, _per_qt, _per_gal, _per_gal_uk, _per_in3, _per_ft3, _per_yd3, _per_ul, _per_cm3; allowed 0–1000000000 /m3 (metric), 0–1000000000 /yd3 (imperial) | optional |
| Parameter | Value | If omitted |
|---|---|---|
area1_shapeShape | one of: rectangle, circle, triangle | counted as rectangle |
area1_length_ftLength | number; any unit in the name: _mm, _cm, _m, _km, _in, _ft, _yd, _mi, _nmi; allowed > 0 – 32808.4 ft; used with area1_shape = rectangle | required |
area1_width_ftWidth | number; any unit in the name: _mm, _cm, _m, _km, _in, _ft, _yd, _mi, _nmi; allowed > 0 – 32808.4 ft; used with area1_shape = rectangle | required |
area1_diameter_ftDiameter | number; any unit in the name: _mm, _cm, _m, _km, _in, _ft, _yd, _mi, _nmi; allowed > 0 – 32808.4 ft; used with area1_shape = circle | required |
area1_base_ftBase | number; any unit in the name: _mm, _cm, _m, _km, _in, _ft, _yd, _mi, _nmi; allowed > 0 – 32808.4 ft; used with area1_shape = triangle | required |
area1_height_ftHeight | number; any unit in the name: _mm, _cm, _m, _km, _in, _ft, _yd, _mi, _nmi; allowed > 0 – 32808.4 ft; used with area1_shape = triangle | required |
Examples
?area1_length_ft=20&area1_width_ft=15&depth_in=4&price_per_yd3=38?area1_shape=circle&area1_diameter_m=6&area2_length_m=5&area2_width_m=3&depth_cm=10&waste_pct=10
Write decimals with a point. Encode a space as %20, + as %2B, # as %23 and & as %26.
Result elements: [data-result-block="material"]