Area and Material Cost Calculator

Length unit

Enter rectangular length and width in the selected unit, subtract openings in squared units, and enter cost per squared unit. Use consistent units throughout.

Results

Enter your values and select Calculate.

A=lw−Ao,C=ApA=lw-A_o,\quad C=Ap

About this tool

The area and material cost calculator finds the area of a rectangular room or surface, subtracts openings, and multiplies by a price per square unit. Homeowners and contractors use it to estimate flooring, carpet, sod, or wall coverings before buying. Area of a rectangle is length times width, and it is measured in square units, such as square meters or square feet.

How it works

Choose meters or feet as the length unit, then enter the length and width of the rectangle in that unit. If part of the surface will not be covered, such as a fireplace hearth or a fitted cabinet, enter its area in square meters or square feet in the Area to subtract field. Finally, enter the price of the material per square unit.

The calculator multiplies length by width, subtracts the openings and multiplies the net area by the unit price. Openings larger than the rectangle are rejected because the area cannot go below zero. Keep the price in the same unit as the area: a price per square foot paired with lengths in meters gives a wrong total.

A=lw−Ao,C=ApA=lw-A_o,\quad C=Ap

Example

With the defaults, length is 5 m and width is 4 m, so the area is 5×4=205\times4=20 square meters. No area is subtracted for openings. At a cost of 10 per square meter, the material cost is 20×10=20020\times10=200. If a 2 square meter section were excluded, the net area would be 18 square meters and the cost 180.

Assumptions and limits

The tool handles one rectangle at a time; measure L-shaped or irregular rooms as separate rectangles and add the results. It does not convert between meters and feet, and it adds no waste allowance. Openings and price must use the same squared unit as the lengths.

Frequently asked questions

How do you calculate square footage?

Measure the length and width in feet and multiply them. A room 12 feet by 10 feet is 120 square feet.

How many square feet are in a square meter?

One square meter is about 10.764 square feet, and one square foot is about 0.0929 square meters. To convert a result, multiply square meters by 10.764 or divide square feet by 10.764. A 20 m² room is therefore about 215 square feet.

How do you find the area of an L-shaped room?

Split the room into rectangles that do not overlap, calculate the area of each, and add them together. For example, an L-shaped room made of a 5 by 4 m section and a 2 by 3 m section covers 20+6=2620 + 6 = 26 m². Run this calculator once per rectangle with the same price, then add the costs.

How much extra material should I buy?

Many flooring guides suggest adding about 5% to 10% for cuts and mistakes, and more for diagonal layouts or rooms with many corners. The right amount depends on the material and the layout.

How do I add a waste allowance to the square footage?

This calculator does not add waste, so increase the area yourself before pricing. For a 10% allowance, multiply the net area by 1.10: 120 square feet becomes 132 square feet. At 3 per square foot, the material cost rises from 360 to 396.

Link with your values

Add these parameters to this page’s address to open it with the values filled in, for example to share a calculation or to link to it from an AI assistant. The result is calculated in the browser: the page HTML shows an example for the default values, and the tool sets the data-url-params attribute once the link’s values are applied.

ParameterValueIf omitted
unitsmetric or imperialset by the first measured value
length_mlength_ftLengthnumber; any unit in the name: _mm, _cm, _m, _km, _in, _ft, _yd, _mi, _nmi; allowed > 0 m (metric), > 0 ft (imperial)required
width_mwidth_ftWidthnumber; any unit in the name: _mm, _cm, _m, _km, _in, _ft, _yd, _mi, _nmi; allowed > 0 m (metric), > 0 ft (imperial)required
openings_area_m2openings_area_ft2Area to subtractnumber; any unit in the name: _cm2, _m2, _ha, _km2, _in2, _ft2, _yd2, _acre; allowed ≥ 0 m2 (metric), ≥ 0 ft2 (imperial)counted as 0
price_per_m2price_per_ft2Cost per square unitamount without a currency symbol; a time per unit in the name: _per_cm2, _per_m2, _per_ha, _per_km2, _per_in2, _per_ft2, _per_yd2, _per_acre; allowed ≥ 0 /m2 (metric), ≥ 0 /ft2 (imperial)default 10

Examples

  • ?length_ft=14&width_ft=12&openings_area_ft2=6&price_per_ft2=4.5
  • ?length_m=6.5&width_m=4&price_per_m2=35

Write decimals with a point. Encode a space as %20, + as %2B, # as %23 and & as %26.

Result elements: [data-result-block="square_footage_calculator"]