About this tool
This paint calculator estimates how many liters of paint a job needs and how many containers to buy. It subtracts doors and windows from the wall area, multiplies by the number of coats and divides by the coverage rate. Coverage is the area one liter of paint covers in a single coat, listed by the manufacturer on the can or data sheet. It is useful for planning room repainting, fences or other flat surfaces.
How it works
Enter the total wall area in square meters, then the combined area of doors, windows and anything else you will leave unpainted. Add the number of coats, the coverage from the can in square meters per liter, and the size of the containers you plan to buy.
The tool subtracts openings from the gross area, multiplies the net area by the number of coats and divides by coverage to get liters. It then divides liters by the container size and rounds up, so the container count always covers the full estimate. Ceilings and trim are separate surfaces: run the calculation again for them, because ceiling paint and gloss often list a different coverage.
Example
With the defaults, the wall area is 100 m², doors and windows take 10 m², you plan two coats, the paint covers 10 m² per liter and it comes in 5 L containers. Net area is m². Paint needed is liters. Dividing by the container size gives , which rounds up to 4 containers, leaving 2 liters spare.
Assumptions and limits
Areas are in square meters and coverage in square meters per liter; feet and gallons are not supported. The estimate uses one coverage rate for every coat and does not add a waste allowance, primer, or extra paint for rough, porous or textured surfaces. Container counts round up to whole containers of one size.
Frequently asked questions
How much area does a liter of paint cover?
Many interior wall paints list coverage of roughly 10 to 12 m² per liter per coat on smooth, primed surfaces. It varies by product and surface, so use the figure on your paint's label.
How many coats of paint do I need?
Two coats are commonly recommended for even color. Large color changes, dark colors or bare surfaces may need a primer or a third coat.
How do I measure wall area?
Multiply the room's perimeter by the wall height, or add up length times height for each wall. Measure doors and windows the same way and enter their total as the area to subtract.
Should I buy extra paint?
A small reserve is useful for touch-ups and for porous or textured surfaces that absorb more paint. Rounding up to whole containers often provides some margin already.
How much paint do I need for a 4 by 5 meter room?
With 2.5 m high walls, the perimeter of 18 m gives m² of wall. Subtracting a door and window of 3.5 m² leaves 41.5 m², and two coats at 10 m² per liter need 8.3 liters. In 5 L containers that rounds up to 2 containers, with 1.7 liters left over for touch-ups.
Link with your values
Add these parameters to this page’s address to open it with the values filled in, for example to share a calculation or to link to it from an AI assistant. The result is calculated in the browser: the page HTML shows an example for the default values, and the tool sets the data-url-params attribute once the link’s values are applied.
| Parameter | Value | If omitted |
|---|---|---|
area_m2Area | number; any unit in the name: _cm2, _m2, _ha, _km2, _in2, _ft2, _yd2, _acre; allowed > 0 m2 | required |
openings_area_m2Area to subtract | number; any unit in the name: _cm2, _m2, _ha, _km2, _in2, _ft2, _yd2, _acre; allowed ≥ 0 m2 | counted as 0 |
coatsNumber of coats | whole number; allowed ≥ 1 | required |
coverage_m2_per_lCoverage per liter | number; any unit in the name: _m2_per_l, _ft2_per_gal; allowed > 0 m2_per_l | default 10 |
container_volume_lContainer volume | number; any unit in the name: _ml, _l, _m3, _tsp, _tbsp, _fl_oz, _fl_oz_uk, _cup, _pt, _qt, _gal, _gal_uk, _in3, _ft3, _yd3, _ul, _cm3; allowed > 0 l | default 5 |
Examples
?area_ft2=400&openings_area_ft2=40&coats=2?area_m2=45&coats=3&coverage_m2_per_l=12&container_volume_l=2.5
Write decimals with a point. Encode a space as %20, + as %2B, # as %23 and & as %26.
Result elements: [data-result-block="paint_calculator"]