Pool Volume Calculator: Gallons, Liters and Fill Time

View results · 22,023 US gal

Pool and water

Units
Pool shape
Floor

Enter the depth of the water, not the height of the wall.

Result

Water volume
US gal
Surface area
512 sq ft
Average depth
5.75 ft
Time to fill
1 day 12 hours
Water per in of depth
319.2 US gal

Volume in every unit

UnitWater volume
Liters (L)83,365
Cubic meters (m³)83.36
US gallons22,023
Imperial (UK) gallons18,338
Cubic feet (ft³)2,944

Chemical labels give doses per 10,000 gallons or per 10 m³ of water: use the volume above with the product's own instructions.

About this tool

Your pool's volume is the starting point for almost everything in pool care. Chemical doses and test-kit instructions are given per 10,000 gallons or per 10 cubic meters, pumps and filters are sized to turn the water over in a set number of hours, and heating costs, water bills and delivery quotes all depend on it.

Enter the depth of the water rather than the height of the walls, because pools are rarely filled to the brim. In US units the volume is the cubic feet times about 7.48 gallons; in metric units each cubic meter is 1,000 liters.

How it works

Choose US units (feet and gallons) or metric (meters and liters), pick the pool shape and enter its inside dimensions. For a flat floor enter one water depth; for a floor that slopes from a shallow end dsd_s to a deep end ddd_d enter both, and the calculator uses the average depth (ds+dd)/2(d_s + d_d)/2. The volume VV is the surface area AA times the average depth.

The surface area is length times width for a rectangle, πd2/4\pi d^2/4 for a round pool and πlw/4\pi l w/4 for an oval. Kidney pools have no exact formula, so the pool trade's rule of thumb 0.45×(WA+WB)×L0.45 \times (W_A + W_B) \times L is used, with WAW_A and WBW_B the widths across the two rounded ends and LL the length. Enter the flow rate of your hose or fill line to estimate how long filling takes.

V=A×ds+dd2V = A \times \frac{d_s + d_d}{2}

Example

A rectangular pool 32 by 16 feet slopes from 3.5 feet to 8 feet. The average depth is (3.5+8)/2=5.75(3.5 + 8)/2 = 5.75 ft, so the volume is 32×16×5.75=294432 \times 16 \times 5.75 = 2944 cubic feet, or 2944×7.48052≈220232944 \times 7.48052 \approx 22023 US gallons. A garden hose delivering 10 gallons a minute needs about 2,202 minutes, a day and a half, to fill it.

A round above-ground pool 24 feet across with 4 feet of water holds π×122×4≈1810\pi \times 12^2 \times 4 \approx 1810 cubic feet, about 13,536 gallons.

Assumptions and limits

The volume assumes straight walls and a floor that slopes evenly from end to end. Many pools have a hopper or a steep drop into the deep end, steps, benches and rounded corners, which change the real volume by several percent, so treat the result as an estimate and use your builder's figure if you have one. The kidney formula is an approximation.

The fill time assumes a steady flow. Hose flow drops with long hoses, low water pressure and other taps running; time how long it takes to fill a bucket of known size to measure your actual rate. Always follow the product label and local rules for chemical doses.

Frequently asked questions

How many gallons are in my pool?

For a rectangular pool, multiply length × width × average depth in feet by 7.48. A 32 × 16 ft pool with an average depth of 5.75 ft holds about 22,000 US gallons. For a round pool, use 3.14 × radius² × depth × 7.48.

How do I work out the average depth of a sloped pool?

Add the shallow-end and deep-end depths and divide by two. A pool 3.5 ft deep at one end and 8 ft at the other has an average depth of 5.75 ft. If the deep end is a short hopper rather than an even slope, the true average is lower.

How do I calculate pool volume in liters?

Work in meters: length × width × average depth gives cubic meters, and each cubic meter is 1,000 liters. A 10 × 5 m pool with an average depth of 1.5 m holds 75 cubic meters, or 75,000 liters.

How long does it take to fill a pool with a garden hose?

Garden hoses commonly deliver roughly 5 to 15 US gallons (20 to 60 liters) a minute, depending on hose size and water pressure, so a 20,000-gallon pool can take a day or more. Time how long your hose takes to fill a bucket of known size and enter that rate above.

How do I find the volume of a kidney-shaped pool?

Measure the length LL and the widths across the two rounded ends, WAW_A and WBW_B. The surface area is about 0.45×(WA+WB)×L0.45 \times (W_A + W_B) \times L; multiply it by the average depth. For a 30 ft pool that is 12 ft and 16 ft wide at the ends, the area is about 0.45×28×30=3780.45 \times 28 \times 30 = 378 square feet.

Link with your values

Add these parameters to this page’s address to open it with the values filled in, for example to share a calculation or to link to it from an AI assistant. The result is calculated in the browser: the page HTML shows an example for the default values, and the tool sets the data-url-params attribute once the link’s values are applied.

ParameterValueIf omitted
unitsmetric or imperialset by the first measured value
shapePool shapeone of: rectangle, round, oval, kidneydefault rectangle
length_mlength_ftLengthnumber; any unit in the name: _mm, _cm, _m, _km, _in, _ft, _yd, _mi, _nmi; allowed > 0 – 200 m (metric), > 0 – 656.1 ft (imperial); used with shape = rectangle, oval, kidneyrequired
width_mwidth_ftWidthnumber; any unit in the name: _mm, _cm, _m, _km, _in, _ft, _yd, _mi, _nmi; allowed > 0 – 200 m (metric), > 0 – 656.1 ft (imperial); used with shape = rectangle, ovalrequired
diameter_mdiameter_ftDiameternumber; any unit in the name: _mm, _cm, _m, _km, _in, _ft, _yd, _mi, _nmi; allowed > 0 – 200 m (metric), > 0 – 656.1 ft (imperial); used with shape = roundrequired
width_a_mwidth_a_ftWidth at end Anumber; any unit in the name: _mm, _cm, _m, _km, _in, _ft, _yd, _mi, _nmi; allowed > 0 – 200 m (metric), > 0 – 656.1 ft (imperial); used with shape = kidneyrequired
width_b_mwidth_b_ftWidth at end Bnumber; any unit in the name: _mm, _cm, _m, _km, _in, _ft, _yd, _mi, _nmi; allowed > 0 – 200 m (metric), > 0 – 656.1 ft (imperial); used with shape = kidneyrequired
depth_modeFloorone of: constant, slopeddefault sloped
depth_mdepth_ftWater depthnumber; any unit in the name: _mm, _cm, _m, _km, _in, _ft, _yd, _mi, _nmi; allowed > 0 – 10 m (metric), > 0 – 32.8 ft (imperial); used with depth_mode = constantrequired
shallow_depth_mshallow_depth_ftShallow end depthnumber; any unit in the name: _mm, _cm, _m, _km, _in, _ft, _yd, _mi, _nmi; allowed > 0 – 10 m (metric), > 0 – 32.8 ft (imperial); used with depth_mode = slopedrequired
deep_depth_mdeep_depth_ftDeep end depthnumber; any unit in the name: _mm, _cm, _m, _km, _in, _ft, _yd, _mi, _nmi; allowed > 0 – 10 m (metric), > 0 – 32.8 ft (imperial); used with depth_mode = slopedrequired
flow_gpmFill ratenumber; allowed > 0 – 264172.0523581484optional
flow_l_per_minFill ratenumber; allowed > 0 – 1000000optional
flow_m3_per_hFill ratenumber; allowed > 0 – 59999.99999999999optional

Examples

  • ?length_ft=32&width_ft=16&shallow_depth_ft=3.5&deep_depth_ft=8&flow_gpm=12
  • ?diameter_m=6&depth_m=1.3&flow_l_per_min=40
  • ?shape=oval&length_ft=30&width_ft=15&depth_ft=5
  • ?length_m=9&width_a_m=3&width_b_m=4&depth_m=1.5&flow_m3_per_h=6

Write decimals with a point. Encode a space as %20, + as %2B, # as %23 and & as %26.

Result elements: [data-result-block="pool-volume"]